Water based acrylic copolymer sealer/primer used as a sealer and / or base coat on hard surfaces. This product is non-toxic and is suitable for vinyl, cement, slate and other hard surfaces..
SEALANT DESCRIPTION
- Easy Application
- Low Odour
- Long-Lasting Antislip Sealer
- Indoors and Outdoors Non-Film Forming
- Low Cost
The sealer is a solvent based blend of a fluorinated copolymer and acrylic resin used for the anti-stain treatment of porous surfaces such as sandstone, slate, concrete, bricks, paving stones, unglazed ceramics, terrazzo, terracotta, etc. The Finish will be dependent on the Satin finish which is selected. Darkening and gloss can be increased with multiple coats. The sealer can be applied to both vertical and horizontal surfaces.
PRODUCT TYPE
Satin 33 [Invisible / Matt finish] | Satin 50 [Semi-gloss finish] | Satin 100 [High-gloss finish]
BENEFITS
- Water repellent
- Oil repellent
- Stain resistance
- Protection against moss
- Colour enhancement
- The surface remains permeable to gas
- Long-lasting
- Environmentally acceptable
The anti-slip sealing is a water-based chemical treatment that increases the co-efficient of friction on slippery when wet ceramic floor tiles. It is not a film-forming coat that can wear off.
BENEFITS
- Easy Application
- Low Odour
- Long-Lasting Antislip Sealer
- Indoors and Outdoors Non-Film Forming
- Low Cost
PLEASE NOTE
THIS PRODUCT CANNOT ELIMINATE THE POSSIBILITY OF SLIPPING.
STERIDISER LQ is a total spectrum disinfectant (effective against bacteria, fungi, viruses and spores). STERIDISER LQ is ideally suited for fighting microorganisms that are spread via droplets as it can be used for aerial as well as surface disinfection. STERIDISER LQ can be used in the presence of humans and animals through misters, humidifiers, sprayers, HP washers and electrical/petrol fogging machines (please note that some of these applicators produce a much-reduced droplet size which can be irritating to the respiratory system – in such cases it is advised to wear a face mask). STERIDISER LQ will not cause fumes, irritation, staining or corrosion. No rinsing is required, and the product is completely biodegradable with a zero rating according to EN standards. Acute toxicity studies complying with current international standard protocols, covering oral, dermal and inhalation toxicity, eye and dermal irritation, and skin sensitization were recently done. These are all supervised GLP (Good Laboratory Practice) studies and were carried out using a non-lethal endpoint control. The results demonstrated that all in-use concentrations were nontoxic. STERIDISER LQ can effectively and safely be used to combat Corona Virus Disease 2019 (abbreviated “COVID-19”). Coronaviruses belong to the family Coronaviridae – they have enveloped viruses that are relatively easily inactivated by STERIDISER LQ. To ensure responsible and practical applications by all end-users, STERIDISER LQ should be used as received without dilution. Using STERIDISER LQ at this concentration will reduce the contact time and overcome the effects of other interfering factors such as dirty conditions and other micro-organisms that may also be present.
BENEFITS
- Economical
- High-level disinfection of surfaces and air spaces
- Effective against bacteria, fungi, viruses, and bacterial and fungal spores
- Non-irritant
- Can be used in the presence of humans and animals
- Non-corrosive
- Non-toxic
- Non-staining
- SANS 636 Compliant
- SANS 1853 Compliant
- WATER BASED ACRYLIC SEALER
-
Water based acrylic copolymer sealer/primer used as a sealer and / or base coat on hard surfaces. This product is non-toxic and is suitable for vinyl, cement, slate and other hard surfaces..
BENEFITS
- Easy Application
- Low Odour
- Long-Lasting Antislip Sealer
- Indoors and Outdoors Non-Film Forming
- Low Cost
- COLOUR ENHANCING SEALER
-
The sealer is a solvent based blend of a fluorinated copolymer and acrylic resin used for the anti-stain treatment of porous surfaces such as sandstone, slate, concrete, bricks, paving stones, unglazed ceramics, terrazzo, terracotta, etc. The Finish will be dependent on the Satin finish which is selected. Darkening and gloss can be increased with multiple coats. The sealer can be applied to both vertical and horizontal surfaces.
PRODUCT TYPE
Satin 33 [Invisible / Matt finish] | Satin 50 [Semi-gloss finish] | Satin 100 [High-gloss finish]
BENEFITS
- Water repellent
- Oil repellent
- Stain resistance
- Protection against moss
- Colour enhancement
- The surface remains permeable to gas
- Long-lasting
- Environmentally acceptable
- ANTI-SLIP TREATMENT
-
The anti-slip sealing is a water-based chemical treatment that increases the co-efficient of friction on slippery when wet ceramic floor tiles. It is not a film-forming coat that can wear off.
BENEFITS
- Easy Application
- Low Odour
- Long-Lasting Antislip Sealer
- Indoors and Outdoors Non-Film Forming
- Low Cost
PLEASE NOTE
THIS PRODUCT CANNOT ELIMINATE THE POSSIBILITY OF SLIPPING. - STERIDISER LQ
-
STERIDISER LQ is a total spectrum disinfectant (effective against bacteria, fungi, viruses and spores). STERIDISER LQ is ideally suited for fighting microorganisms that are spread via droplets as it can be used for aerial as well as surface disinfection. STERIDISER LQ can be used in the presence of humans and animals through misters, humidifiers, sprayers, HP washers and electrical/petrol fogging machines (please note that some of these applicators produce a much-reduced droplet size which can be irritating to the respiratory system – in such cases it is advised to wear a face mask). STERIDISER LQ will not cause fumes, irritation, staining or corrosion. No rinsing is required, and the product is completely biodegradable with a zero rating according to EN standards. Acute toxicity studies complying with current international standard protocols, covering oral, dermal and inhalation toxicity, eye and dermal irritation, and skin sensitization were recently done. These are all supervised GLP (Good Laboratory Practice) studies and were carried out using a non-lethal endpoint control. The results demonstrated that all in-use concentrations were nontoxic. STERIDISER LQ can effectively and safely be used to combat Corona Virus Disease 2019 (abbreviated “COVID-19”). Coronaviruses belong to the family Coronaviridae – they have enveloped viruses that are relatively easily inactivated by STERIDISER LQ. To ensure responsible and practical applications by all end-users, STERIDISER LQ should be used as received without dilution. Using STERIDISER LQ at this concentration will reduce the contact time and overcome the effects of other interfering factors such as dirty conditions and other micro-organisms that may also be present.
BENEFITS
- Economical
- High-level disinfection of surfaces and air spaces
- Effective against bacteria, fungi, viruses, and bacterial and fungal spores
- Non-irritant
- Can be used in the presence of humans and animals
- Non-corrosive
- Non-toxic
- Non-staining
- SANS 636 Compliant
- SANS 1853 Compliant
SERVICES OFFERED
DEEP CLEANING
The Sealing Company is able to deep clean surfaces with an industrial scrubbing machine using water and specialised hard or soft brushes based on the surface and severity of dirt. Deep cleaning surfaces are achieved by manually scraping and brushing any excess dirt, paint, grime or cement which our brick paver cleaning machines might have missed. Depending on the resistance of the dirt we may at times need to apply a bio-friendly soap (in extreme conditions) but will not affect the deep cleaning cost. The newly cleaned surface must be left to dry for +/- 2 hours weather permitting
APPLICATION OF SEALER
Once the desired surface has been left to dry and the Sealing Company is confident that the excess dirt has been removed, we will then start applying the first coat of paver sealer. The brick sealer is applied using a specially designed air spray gun to guard against streak marks and product pooling. Once the first brick sealer coat has been left to air-dry [approximately 45 minutes] the Sealing Company can then start applying the second paver sealer coat.
COLOUR ENHANCING BRICK SEALER APPLICATION
After the brick paver deep cleaning process is complete and the Sealing Company is confident all excess dirt has been removed, we will then start applying the first coat of brick paver sealer once the surface is dry. The product is applied using a specially designed air spray gun to guard against streak marks and sealer pooling. Once the first brick sealer coat has been left to air-dry [approximately 45 minutes] the Sealing Company can then start applying the second coat. The second sealing coat is mixed with a specialized tint that does not react with the brick sealant in any way other than to enhance the existing colour and better the appearance drastically.
APPLICATION OF ANTI-SLIP SEALER TREATMENT
After the brick paver deep cleaning process is complete and the Sealing Company is confident all excess dirt has been removed, we will then start applying the anti-slip treatment. The anti-slip treatment is applied using a pump spray. The anti-slip treatment is left on the applied surface for roughly 5 – 10 minutes to etch the surface [dependant on the surface being treated] before rinsing off with water.
SUPPLY OF PAVER SEALER AND MORE
As a result of our confidence in our sealing products we have made these available to the general public and professionals countrywide. Our floor sealing products can be purchased in various quantities according to the area of application needed. Are you a DIY fundi and looking to protect your investment and enhance your space? The Sealing Company provides:
- Paver Sealing products
- Interior Brick Sealer
- Invisible Sealer
- Pavement Sealer
- Patio Paver sealer
- Wet Look Paver Sealer
SUPPLY OF DISINFECTANTS
STERIDISER LQ is a total spectrum disinfectant (effective against bacteria, fungi, viruses and spores). STERIDISER LQ is ideally suited for fighting microorganisms that are spread via droplets as it can be used for aerial as well as surface disinfection. The disinfectant can be applied in various methods such as wipe or spray; we prefer the pressurised spray method as this in our opinion is most effective as this enables the applicator to move about in a timeous manner as well as preventing surface contact therefore avoiding a higher risk of contamination. In the instance of hand sanitation the obvious choice would be spray and rub.